Tapes II International product technical data

Tapes II International Product Technical Data

PRODUCTS

GENERAL INDUSTRIAL LINE

T-10 GUM KRAFT TAPE
T-20 REINFORCED GUM KRAFT TAPE

MASKING TAPE

T-30        GENERAL PURPOSE
T-31        MEDIUM TEMPERATURE
T-32        HIGH TEMPERATURE
T-33        SOLDER WAVE TAPE
T-35        FLAT BACK MASKING
T-40        FILAMENT TAPE

ESD CELLOPHANE TAPE

T-50 SMALL ROLL (36 YRDS.)
T-51 LARGE ROLL (72 YRDS.)

MAGIC MENDING TAPE

T-60        SMALL ROLL (36 YRDS.)
T-61        LARGE ROLL (72 YRDS.)
X-65        LOW STATIC MASKING TAPE
T-70        CARTON SEALING (TAN&CLEAR)
T-71        3.5 MIL CARTON SEALING TAPE
T-80        SILVER DUCT TAPE
T-81        COLORED CLOTH TAPE
T-91        2 MIL TRANSFER TAPE
T-92        D/F PAPER TAPE
T-93        D/F FILM TAPE
T-95        5 MIL TRANSFER TAPE
T-97        D/F UPVC - 9 MIL
T-98        D/F CLOTH TAPE

FOAM TAPE

T-100      S/F FOAM-WHITE POLYETHYLENE
T-200      S/F VINYL FOAM-GRAY, BLACK
T-300      S/F NEOPRENE FOAM-BLACK
T-545      D/F POLYETHYLENE FOAM-ACRYLIC
T-690      POLYETHYLENE FOAM RUBBER
T-750      VHB D/F TAPE

DISPENSERS

T-500 CARTON SEALING-PISTOL GRIP
T-525 D/F TAPE DISPENSER
T-550 AUTOMATIC LABEL DISPENSER/AUTOMATIC TAPE DISPENSER
T-6          6" WIDE DISPENSER
T-12        12" WIDE DISPENSER
T-18        18" WIDE DISPENSER

HEAVY DUTY DESK DISPENSERS

T-D1      1" WIDTH
T-D2      2" WIDTH
T-D3      3" WIDTH

ANTI-STATIC DESK DISPENSERS

T-D1-AS 1" WIDTH
T-D2-AS 2" WIDTH
T-D3-AS 3" WIDTH
T-1800 ELECTRONIC 2" WIDTH

AUTOMATIC TAPE DISPENSERS

T-6         6" WIDE DISPENSER
T-12       12" WIDE DISPENSER
T-18       18" WIDE DISPENSER

SPECIALTY PRODUCTS

T-605A    PIPE WRAP - TEFLON
T-607      GLASS CLOTH TAPE
T-609      UHMW TAPE
T-610      POLYESTER FILM
T-611      TEFLON PTFE SKIVED TAPE
T-612      TEFLON COATED GLASS TAPE
T-800      ALUMINUM FOIL
T-800C ALUMINUM FOIL-CONDUCTIVE
T-801      LEAD FOIL
T-802      YELLOW (NON-ADHESIVE) VINYL
T-803      COLORED 5 MIL VINYL TAPES
T-804      FLOOR TAPE-DIAGONAL STRIPES
T-804C    PRINTED ESD FLOOR TAPE
T-805      KAPTON TAPES (805,EZ, AS & 3.5MIL)
T-806      POLYMIDE FILM TAPE
T-810      LITHO TAPE
T-807      CIRCUIT BOARD TAPE
T-811      OUTDOOR MASKING -BLUE
T-900      STRETCH WRAP 12", 15", 18"(70,80,90 GAUGE)
T-905      CLEAN ROOM TAPE
T-910      HOOK AND LOOP-VELCRO
T-915      COPPER FOIL EMI/RFI
T-915C    COPPER FOIL-CONDUCTIVE
T-920      PROTECTIVE FILM
T-930      PROTECTIVE PAPER
T-970      POWDER COATING TAPE
T-980      HOT AIR LEVELING TAPE
T-997      GRID TAPE ANTI-STATIC

TECHNICAL DATA

T-30 GENERAL PURPOSE MASKING TAPE

DESCRIPTION:
T-30 IS A GENERAL PURPOSE GRADE MASKING TAPE WITH RUBBER BASED ADHESIVE.

USES:
LIGHT DUTY MASKING/PACKAGING. HOLDING AND TABBING. COMMERCIAL AND RESIDENTIAL PAINTING AND CONSTRUCTION.

FEATURES:
EASY RELEASE OFF THE ROLL, FLEXIBLE. CONFORMS WELL TO IRREGULARLY SHAPED SURFACES. GOOD PRESSURE SENSITIVE QUALITIES. RESISTS WATER, SOLVENTS AND OILS.

PHYSICAL PROPERTIES:

THICKNESS: 5.7 MILS
TENSILE STRENGTH: 23 LBS./IN WIDTH
ELONGATION: 9 %
TEAR RESISTANCE: 11
ADHESION TO STAINLESS STEEL: 39 OZ./IN WIDTH
HEAT RESISTANCE: 180°F / 82 °C
APPLICABLE SPECS.: A-A-883B

PHYSICAL AND PERFORMANCE CHARACTERISTICS SHOWN ABOVE ARE OBTAINED FROM TESTS RECOMMENDED BY PSTC, ASTM, OR GOVERNMENT AGENCIES.

THIS MATERIAL DOES NOT PRODUCE STATIC ELECTRICITY.

STORAGE AND USAGE CONDITIONS:
TAPE SHOULD BE STORED IN ITS ORIGINAL PACKAGE IN A COOL, DRY AREA AWAY FROM DIRECT SUNLIGHT AND SHOULD BE USED WITHIN 12 MONTHS OF DATE OF SHIPMENT. SURFACES TO WHICH THE TAPE IS APPLIED SHOULD BE CLEAN AND FREE OF GREASE, OIL OR OTHER CONTAMINANTS.

T-31 MEDIUM TEMPERATURE MASKING TAPE

DESCRIPTION:
T-31 IS A MEDIUM TEMPERATURE INDUSTRIAL GRADE MASKING TAPE WITH A RUBBER BASED ADHESIVE.

USES:
PAINT MASKING FOR SUBSTRATES SUCH AS METAL, PLASTIC AND RUBBER WHEN USED WITH HIGH TECH, INDUSTRIAL PAINT SYSTEMS, WHICH REQUIRE A HIGH PERFORMANCE TAPE.

FEATURES / BENEFITS:
EXCELLENT CONFORMABILITY.
DESIGNED TO MEET THE DEMANDING REQUIREMENTS OF TODAY'S HIGH TECH INDUSTRIAL PAINT SYSTEMS.
STRIPS CLEANLY WITH NO RESIDUE OR PAINT FLAKE OFF AFTER OVEN BAKING AND EXTENDED APPLICATION PERIODS.
EXCELLENT QUICK STICK.
TAPE LAYS FLAT THUS GIVING CLEAN EDGES.

PHYSICAL PROPERTIES:
BACKING MATERIAL CREPE PAPER
ADHESION TO STEEL 32(OZ/IN. WIDTH)
QUICK STICK 16 (OZ/IN)
ELONGATION 11%
GAUGE 6 .7 MIL.
HEAT RESISTANCE FOR (FOR ONE HR) 150°F, 66°C
APPLICABLE SPECIFICATIONS A-A-883B

PHYSICAL AND PERFORMANCE CHARACTERISTICS SHOWN ABOVE ARE OBTAINED FROM TESTS RECOMMENDED BY PSTC, ASTM, OR GOVERNMENT AGENCIES . INDIVIDUAL ROLLS MAY VARY SLIGHTLY FROM THESE AVERAGES. THE USER SHOULD DETERMINE WHETHER THE PRODUCT IS FIT FOR A PARTICULAR PURPOSE AND IS SUITABLE FOR THE USERS METHOD OF APPLICATION BEFORE USE.

STORAGE AND USAGE CONDITIONS:
TAPE SHOULD BE STORED IN A COOL DRY AREA AWAY FROM DIRECT SUNLIGHT AND SHOULD BE USED WITHIN12 MONTHS FROM DATE OF SHIPMENT. SURFACE TO WHICH TAPE IS APPLIED SHOULD BE CLEAN AND FREE OF GREASE AND OIL OR OTHER CONTAMINANTS.

T-32 HIGH TEMPERATURE MASKING TAPE

DESCRIPTION:
T-32 IS A HIGH-TEMP SUPERIOR STAIN RESISTANT MASKING TAPE.

USES:
CRITICAL HIGH TEMPERATURE PAINT MASKING. MASKING OF PAINTED METAL, PLASTIC AND RUBBER SURFACES WHERE STAINING COULD BE A PROBLEM. HIGH TEMPERATURE HOLDING AND SPLICING APPLICATIONS. INDUSTRIAL BUNDLING USES.

FEATURES / BENEFITS:
CONSTRUCTED WITH SMOOTHER CREPED BACKING, IT PROVIDES FOR FINER PAINT EDGE AND SUPERIOR COLOR SEPARATION. THE SATURANT USED RESULTS IN EXCELLENT CONFORMABILITY AND ELONGATION WHILE MAINTAINING TENSILE STRENGTH AND EDGE TEAR RESISTANCE. A SPECIAL RELEASE COAT ELIMINATES PAINT AND PRIMER FLAKING PROBLEMS, RESISTS SOLVENT PENETRATION AND PROVIDES FOR A CONTROLLED UNWIND. PRIMING OF THE TAPE BACKING ELIMINATES ADHESIVE DEPOSITION DURING REMOVAL. UTILIZING A DUAL CURED ADHESIVE, T-32 RESISTS STAINING AND HAS SUPERIOR HEAT RESISTANCE EVEN TO TEMPERATURES OF 350 DEG. F FOR 1 HOUR.

PHYSICAL PROPERTIES:
BACKING MATERIAL: CREPE PAPER
ADHESION TO STEEL: 34
QUICK STICK (oz/in): 15
TENSILE (lbs/in:) 20
ELONGATION (%): 6 min.
GAUGE (mils): 6.1
HEAT RESISTANCE: 350°F FOR 1 HOUR
SPECIFICATIONS: UTT 106D TYPE 1
PPPT 42C TYPE 1
CID-A-A883A TYPE 1
COMPLIES WITH MIL - T21595D TYPE 1

EQUIVALENT PRODUCTS:
3M #232- #213

NOTE: BECAUSE OF THE RUBBER BASED ADHESIVE AND THE CREPE PAPER CONSTRUCTION THIS PRODUCT DOES NOT PRODUCE STATIC ELECTRICITY.

T-33 SOLDER WAVE MASKING TAPE

DESCRIPTION:
T-33 IS A SUPERIOR STAIN RESISTANT HIGH TEMPERATURE MASKING TAPE. CONSTRUCTED WITH A SMOOTHER CREPE BACKING, IT PROVIDES FOR A FINER PAINT EDGE AND SUPERIOR COLOR SEPARATION. A SPECIAL RELEASE COAT ELIMINATES PAINT AND PRIMER FLAKING PROBLEMS, RESISTS SOLVENT PENETRATION AND PROVIDES FOR A CONTROLLED UNWIND. PRIMING OF THE TAPE BACKING ELIMINATES ADHESIVE DEPOSITION DURING REMOVAL. UTILIZING A DUAL CURED ADHESIVE, T-33 RESISTS STAINING AND HAS SUPERIOR HEAT RESISTANCE EVEN AT TEMPERATURES OF 350 deg. F FOR ONE HOUR.

USES:
T-33 CAN BE USED IN CRITICAL HIGH TEMPERATURE PAINT MASKING. MASKING OF PAINTED METAL, PLASTIC AND RUBBER SURFACES WHERE STAINING COULD BE A PROBLEM. HIGH TEMPERATURE HOLDING AND SPLICING APPLICATIONS. INDUSTRIAL BUNDLING USES.

PHYSICAL PROPERTIES:
BACKING MATERIAL: CREPE PAPER
ADHESION TO STEEL: 34 OZ / IN.
QUICK STICK: 15 OZ / IN
TENSILE STRENGTH: 20 LBS / IN
ELONGATION: 6 % MIN.
THICKNESS: 6.1 MILS.
HEAT RESISTANCE: 350 DEG F - 1 HOUR

SPECIFICATIONS
UUT 106D TYPE 1
PPPT42C TYPE 1
CID A- A -883A TYPE 1
COMPLIES WITH MIL - T21595D TYPE 1

EQUIVALENT TO 3M # 232 - #213

T-40 FILAMENT TAPE

DESCRIPTION:
T-40 IS A GENERAL GRADE GLASS REINFORCED STRAPPING TAPE. THE POLYESTER BACKING IS NON SPLITTING AND NON CRACKING. GOOD ADHESION AND SHOCK RESISTANT PROPERTIES.

PHYSICAL PROPERTIES:
THICKNESS: 5.5 MIL
TENSILE STRENGTH: 130 LBS./ IN
ELONGATION: 4 %
ADHESION TO STEEL: 40 OZ / IN

T-50 / T-51 CELLOPHANE ANTI-STATIC

DESCRIPTION:
T-50 AND T-51 ARE TRANSPARENT, BIODEGRADABLE CELLOPHANE TAPES.THEY ARE HAND TEARABLE, WITH EXCELLENT TACK AND HIGH HOLDING POWER. T-50 IS MANUFACTURED ON A 1'' CORE AND IS 36 YARDS TO A ROLL. T-51 IS MANUFACTURED ON A 3" CORE AND IS 72 YARDS. LONG. BOTH TAPES ARE STATIC FREE.

USES:
T-50 AND T-51 ARE USED AS GENERAL PURPOSE HOLDING, BINDING, AND EDGING TAPES.

PHYSICAL PROPERTIES:
THICKNESS: 2.2 MILS
ADHESIVE: RUBBER
TENSILE STRENGTH: 21 LBS / IN
ADHESION TO STEEL: 60 OZ / IN
ELONGATION: 20%
TEMPERATURE RESISTANCE: 32°F-150°F
SPECIFICATION: CID-AA-113B, TYPE I, CLASS A

T-60 / T-61 MAGIC MENDING FILM TAPE

DESCRIPTION:
T-60 AND T-61 ARE ACETATE FILM TAPES WITH A MATTE FINISH THAT BECOMES INVISIBLE UPON APPLICATION. EXCELLENT HOLDING POWER. T-60 IS MANUFACTURED ON A 1 " CORE AND IS 1296 " LONG. T-61 IS MANUFACTURED ON A 3" CORE AND IS 2592" LONG.

USES:
FOR GENERAL OFFICE USE, T-60 AND T-61 CAN BE WRITTEN ON FOR LABELING. EXCELLENT FOR PERMANENT MENDING, HOLDING AND SPLICING APPLICATIONS.

PHYSICAL PROPERTIES:
THICKNESS: 2.4 MIL
ADHESIVE: ACRYLIC
TENSILE STRENGTH: 20 LBS./ IN
ADHESION TO STEEL: 30 OZ / IN
ELONGATION: 25 %
TEMPERATURE RESISTANCE: 32°F - 150°F

SPECIFICATION: CID-AA-13B, TYPE II, CLASS A

T-70 CARTON SEALING TAPE

DESCRIPTION:
T-70 IS A TRANSPARENT POLYPROPYLENE FILM TAPE WITH AN AGGRESSIVE ACRYLIC ADHESIVE SYSTEM.

FEATURES:
T-70 ADHESIVE WILL NOT DISCOLOR. GOOD MOISTURE AND IMPACT RESISTANCE. T-70 IS AVAILABLE IN TAN OR CLEAR. ALL TEMPERATURE PERFORMANCE.

PHYSICAL PROPERTIES:
BACKING: 1.0 MIL POLYPROPYLENE
COLOR: TAN OR CLEAR
ADHESIVE: ACRYLIC
THICKNESS: 1.7 MIL
ADHESION TO STEEL: 46 OZ / IN
QUICK STICK TO KRAFT: 7 OZ/IN
QUICK STICK TO STEEL: 30 OZ / IN
TENSILE STRENGTH: 20 LBS/ IN
ELONGATION: 120 %
GOV'T SPECS.: PPP-T-70A, (CLEAR ONLY)

T-71 CARTON SEALING TAPE 3.5 MIL CLEAR

DESCRIPTION:
T-71 IS A TRANSPARENT POLYPROPYLENE FILM TAPE WITH AN AGGRESSIVE ACRYLIC ADHESIVE SYSTEM. ADHESIVE WILL NOT DISCOLOR. GOOD MOISTURE AND IMPACT RESISTANCE. AVAILABLE IN TAN OR CLEAR.

PHYSICAL PROPERTIES:
THICKNESS: 3.5 MIL
TENSILE STRENGTH: 75 LBS/ IN
ELONGATION: 100 %
ADHESION TO STEEL: 35 OZ /IN

T-80 DUCT TAPE

DESCRIPTION:
T-80 IS A GENERAL PURPOSE DUCT TAPE WITH A RUBBER ADHESIVE SYSTEM.

FEATURES:
AVAILABLE IN MANY COLORS. GOOD FOR WATERPROOF PACKAGING, BUNDLING, PATCHING, SEALING,
WRAPPING AND COLOR-CODING.

AVAILABLE COLORS:
BEIGE (BEI) BROWN (BRN) GREEN (GRN) PURPLE (PRP) WHITE (WHT) BLACK (BLK) BURGUNDY (BRG) OLIVE DRAB (OLV) RED (RD) YELLOW (YEL) BLUE (BLU) FLORAL GREEN (FGRN) ORANGE (ORG) SILVER (SIL)

PHYSICAL PROPERTIES:
BACKING: WATERPROOF POLYETHYLENE FILM
CARRIER: POLYESTER / COTTON BLEND CLOTH
ADHESIVE: NATURAL RUBBER
TENSILE STRENGTH: 22 LBS / IN WIDTH
ADHESION TO STEEL: 43 OZ /IN WIDTH
THICKNESS: 9.0 MIL
ELONGATION: 10 %
MAXIMUM TEMPERATURE: 200°F

MEETS REQUIREMENTS OF UL 723
FLAME SPREAD INDEX 5
SMOKE DEVELOPMENT INDEX 20

T-91 ACRYLIC TRANSFER TAPE 2 MIL

DESCRIPTION:
T-91 IS AN ACRYLIC TRANSFER TAPE THAT CAN BE USED FOR GAP FILLING, MOUNTING AND LAMINATING. T-91 ALSO BONDS WELL TO MANY IRREGULAR OR TEXTURED SURFACES.

FEATURES / BENEFITS:
T-91 OFFERS A HIGH INITIAL ADHESION, GOOD SHEAR HOLDING POWER AND EASE OF SLITTING DUE TO FIBROUS CONTENT.

PHYSICAL PROPERTIES:
ADHESIVE: ACRYLIC
THICKNESS W/OP LINER: 2.0 MIL
LINER: HEAT AND MOISTURE STABLE SILICONE COATED PAPER
COLOR: CLEAR
ADHESION TO STEEL: 72 OZ / IN WIDTH
LOW TEMPERATURE APPLICATION: 10° F
HEAT RESISTANCE: 250°F
CHEMICAL RESISTANCE: (SOLVENT) MEDIUM - HIGH

NOTE:
THE SURFACE TO WHICH THE TAPE IS APPLIED SHOULD BE DRY, CLEAN AND FREE OF GREASE AND OIL. TAPE SHOULD BE STORED IN A COOL DRY AREA, AT TEMPERATURES OF 60 DEG. F. TO 80° F.

T-92-247 BLACK TISSUE

DESCRIPTION:
T-92-247 IS A DOUBLE COATED BLACK TISSUE WITH A POLYETHYLENE COATED KRAFT PAPER RELEASE LINER.

FEATURES / BENEFITS:
T-92-247 IS CONSTRUCTED WITH BLACK ADHESIVE AND TISSUE FOR THE BEST SHADING.EXCELLENT BONDING TO RUBBER MATERIALS. ANTI-AGING AND ALSO A GOOD RESISTANCE TO SOLVENTS, CHEMICALS AND OILS.

USES:
T-92-247 CAN BE USED TO SPLICE PLASTIC FILM, PAPER AND FOIL. IT CAN ALSO BE USED TO FASTEN COMPONENTS SUCH AS MIRROR TILES, PLATES, MACHINE TOOLS AND NAMEPLATES. THE SPECIAL ADHESIVE SYSTEM IS ALSO GREAT FOR LAMINATING AND BONDING RUBBER ITEMS.

PHYSICAL PROPERTIES:
ADHESIVE: BLACK ACRYLIC BASE (SOLVENT TYPE)
CARRIER: BLACK TISSUE
LINER: KRAFT PAPER POLYETHYLENE COATED
THICKNESS: 5.5 MIL

T-92 DOUBLE FACED PAPER

DESCRIPTION:
T-92 IS DOUBLE COATED CREPE PAPER. A 3.5 MIL IMPREGNATED CREPE PAPER, COATED ON BOTH SIDES WITH A SYNTHETIC BASED ADHESIVE. THE ADHESIVE EXHIBITS ULTRA HIGH TACK AND MODERATE DEAD LOAD PROPERTIES. THE TAPE IS SUPPLIED ON A STANDARD 60 LB. SILICONE TREATED RELEASE PAPER. APPLICATIONS WHERE AN ECONOMICAL, GENERAL PURPOSE DOUBLE COATED TAPE WITH GOOD TENSILE STRENGTH AND ADDITIONAL THICKNESS STRENGTH IS NEEDED FOR BONDING, LAMINATING OR HOLDING. USEFUL FOR HOLDING WOOD CUTS AND DIES.

PHYSICAL PROPERTIES:
THICKNESS: 6.0 MIL
ADHESIVE: SYNTHETIC RUBBER
PEEL ADHESION (OZ / IN WIDTH): 60 LBS.

T-93 DOUBLE FACED FILM TAPE

DESCRIPTION:
T-93 IS A DOUBLE COATED POLYESTER FILM PRESSURE SENSITIVE TAPE WITH ACRYLIC ADHESIVE FOR HIGH TEMPERATURE APPLICATIONS.

USES:
T-93 IS USED IN THE BONDING OF FILMS AND CLEAR PLASTICS. T-93 BONDS A WIDE VARIETY OF RIGID AND FLEXIBLE SUBSTRATES. T-93 IS ALSO GOOD FOR MOUNTING NAMEPLATE APPLICATIONS AND DECORATIVE WALL PRODUCTS.

FEATURES / BENEFITS:
T-93 IS A TRANSPARENT PRODUCT WHICH IS COATED WIT AN EXTREMELY AGGRESSIVE ACRYLIC ADHESIVE OFFERING SERVICE TEMPERATURES FROM -10 DEG F TO 255 DEG F, AND APPLICATION TEMPERATURES FROM 10 DEG F TO 120 DEG F

PHYSICAL PROPERTIES:
SUBSTRATE: .5 MIL POLYESTER FILM
ADHESIVE: ACRYLIC (CLEAR)
THICKNESS W/O LINER: 3.5 MIL
LINER THICKNESS: 3.5 MIL (60 LBS)
COLOR: TRANSPARENT
ADHESION TO STEEL: 80 OZ/IN WIDTH
TENSILE STRENGTH: 8 LBS / IN WIDTH
ELONGATION: 10 %

T-93-8B DOUBLE SIDED FILM TAPE

DESCRIPTION:
T-93-8B CONSISTS OF A POLYESTER CARRIER COATED ON ONE SIDE WITH AN AGGRESSIVE ACRYLIC PRESSURE SENSITIVE ADHESIVE, THEN COATED ON THE OTHER SIDE ACRYLIC REMOVABLE ADHESIVE.THIS PRODUCT IS SELF WOUND ON A COATED TWO SIDE DEFINED KRAFT RELEASE LINER.

USES:
T-93-8B IS IDEAL FOR LAMINATING TO A WIDE VARIETY OF MATERIALS. IT OFFERS EXCELLENT ADHESION, STABILITY AND DIE-CUTTING CAPABILITIES ALSO A REMOVABLE ADHESIVE FOR THE END USER.

PHYSICAL PROPERTIES:
CARRIER THICKNESS: .5 MIL
RELEASE LINER: 80 # C2S
TEMPERATURE APPLICATION: 40 DEG F - 80 DEG F
TEMPERATURE SERVICE: 0°F - 160°F
TENSILE STRENGTH 6.5 LBS. / IN WIDTH
ELONGATION: 100 %
ADHESIVE EXPOSED SIDE: 1.5 MIL
ADHESIVE LINER SIDE: 1.5 MIL
ADHESION TO STEEL: 75 OZ / LIN IN.

T-94 DOUBLE COATED CLOTH TAPE

DESCRIPTION:
T-94 HIGH ADHESION, DOUBLE COATED, NATURAL CLOTH TAPE WITH SILICONE COATED RELEASE LINER.

USES:
INSTALLATION OF CARPET FOR PROFESSIONAL GRADE REQUIREMENTS. T-94 IS IDEAL FOR EXHIBITORS AND AIRLINES. MOUNTING OF NAMEPLATES AND TROPHY FACINGS. HEAVY DUTY INDUSTRIAL MOUNTING AND SPLICING APPLICATIONS.

FEATURES / BENEFITS:
HIGH ADHESION HOLDS SURFACES TOGETHER UNDER DEMANDING SHEAR CONDITIONS. T-94 IS FLEXIBLE AND CONFORMS READILY TO IRREGULAR SURFACES. HIGH TENSILE STRENGTH ASSURES PERFORMANCE UNDER STRESS.

PHYSICAL PROPERTIES:
TENSILE STRENGTH: 53 LBS / IN WIDTH
ADHESION TO STEEL: 50 + OZ / IN WIDTH
THICKNESS: 11 MIL
ADHESIVE: RUBBER BASE / SOLVENT DISPERSED
COLOR: NATURAL WHITE, LINER AND ADHESIVE

T-95 ACRYLIC TRANSFER TAPE 5 MIL

DESCRIPTION:
T-95 IS AN ACRYLIC TRANSFER TAPE.

USES :
T-95 CAN BE USED FOR GAP FILLING, MOUNTING, LAMINATING AND BONDS TO MANY IRREGULAR OR TEXTURED SURFACES.

PHYSICAL PROPERTIES:
ADHESIVE: ACRYLIC
THICKNESS W/O LINER: 5.0 MIL
LINER: SILICONE COATED PAPER
COLOR: CLEAR
ADHESION TO STEEL: 72 OZ/IN WIDTH
LOW TEMPERATURE APPLICATION: 10°F
HEAT RESISTANCE: 250°F
CHEMICAL RESISTANCE: MEDIUM - HIGH

T-97 DOUBLE FACED UPVC TAPE

DESCRIPTION:
T-97 IS A STRONG ACRYLIC ADHESIVE WITH WHITE UPVC FILM THAT PROVIDES EXCELLENT SHEAR STRENGTH. LIGHT AND AGE RESISTANT.

USES:
T-97 IS USED FOR MOUNTING TROPHY NAMEPLATES, HEAVY SIGNS OR OTHER MOUNTING REQUIREMENTS. ADHERES WELL TO METALLIC MATERIALS, ENAMELED SURFACES AND PLASTICS.

PHYSICAL PROPERTIES:
THICKNESS: 9 MIL
ADHESIVE: ACRYLIC
CARRIER: UPVC
ADHESION TO STEEL: 75 OZ/ IN WIDTH
TEMPERATURE: LONG TERM 145°F, SHORT TERM 160°F

T-100 SINGLE FACED FOAM

DESCRIPTION:
T-100 IS A PRESSURE SENSITIVE ADHESIVE COATED, CLOSED CELL POLYETHYLENE BASED FOAM TAPE. THE HIGH PERFORMANCE ACRYLIC PRESSURE SENSITIVE ADHESIVE OFFERS APPLICATION TO MOST SURFACES AND PROVIDES EXCELLENT PERFORMANCE WHEN EXPOSED TO ENVIRONMENTAL EXTREMES OF VIBRATION, TEMPERATURE AND HUMIDITY. THE SOFT AND RESILIENT POLYETHYLENE FOAM PROVIDES LOW MOISTURE ABSORPTION AND RETAINS FLEXIBILITY OVER A WIDE TEMPERATURE RANGE.

USES:
T-100 IS COMMONLY USED IN CUSHIONING, INSULATING SEALING AND GASKET APPLICATIONS.

PHYSICAL PROPERTIES:
ADHESION TO STEEL: 40 OZ / IN
CHEMICAL RESISTANCE: GOOD
MOISTURE AND FUNGUS RESISTANCE: GOOD
WATER ABSORPTION: .64 OZ /SQ. FT. OF SLIT SURFACE
THERMAL CONDUCTIVITY: .30 K- FACTOR AT 70°F
APPLICATION TEMPERATURE: 50°F - 100°F

SHELF LIFE:
1 YEAR FROM DATE OF PURCHASE, WHEN STORED IN A COOL DRY AREA, FREE FROM EXPOSURE TO EXCESSIVE HEAT, MOISTURE OR DIRECT SUNLIGHT.

T-118 SOLDER WAVE TAPE

DESCRIPTION:
T-118 IS A SUPERIOR STAIN RESISTANT, HIGH TEMPERATURE MASKING TAPE. CONSTRUCTED WITH A SMOOTHER CREPE BACKING, IT PROVIDES FOR A FINER PAINT EDGE AND SUPERIOR COLOR SEPARATION. THE SATURANT USED RESULTS IN EXCELLENT CONFORMABILITY AND RESISTANCE TO MANY SUBSTANCES. A SPECIAL RELEASE COAT ELIMINATES PAINT AND PRIMER FLAKING PROBLEMS, RESISTS SOLVENT PENETRATION AND PROVIDES FOR A CONTROLLED UNWIND. PRIMING OF THE TAPE BACKING ELIMINATES ADHESIVE DEPOSITION DURING REMOVAL. UTILIZING A DUAL CURED ADHESIVE, T-118 RESISTS STAINING AND HAS SUPERIOR HEAT RESISTANCE EVEN AT TEMPERATURES OF 350°F FOR 1 HOUR.

USES:
T-118 CAN BE USED IN CRITICAL HIGH TEMPERATURE PAINT MASKING. MASKING OF PAINTED METAL, PLASTIC AND RUBBER SURFACES, WHERE STRAINING COULD BE A PROBLEM. HIGH TEMPERATURE HOLDING AND SPLICING APPLICATIONS.

PHYSICAL PROPERTIES:
BACKING MATERIAL: CREPE PAPER
ADHESION TO STEEL: 34 OZ / IN WIDTH
QUICK STICK: 15 OZ/ IN WIDTH
TENSILE STRENGTH: 20 LBS / IN WIDTH
ELONGATION 6% MIN.
GAUGE 6.1 MIL
HEAT RESISTANCE 350°F FOR 1 HOUR

SPECIFICATIONS:
106D TYPE 1
PPPT42C TYPE 1
CID A-A-883A TYPE 1
COMPLIES WITH MIL -T21595D TYPE 1

EQUIVALENT TO 3M # 232 AND 213

T-200 VINYL FOAM TAPE

DESCRIPTION:
T-200 IS A PRESSURE SENSITIVE DIRECT ADHESIVE COATED CLOSED CELL PVC (VINYL) BASED FOAM TAPE. THE HIGH PERFORMANCE RUBBER BASED PRESSURE SENSITIVE ADHESIVE OFFERS APPLICATION TO MOST SURFACES AND PROVIDES EXCELLENT PERFORMANCE WHEN EXPOSED TO ENVIRONMENTAL EXTREMES OF VIBRATIONS, TEMPERATURE AND HUMIDITY.

USES:
T-200 IS COMMONLY USED AS A POSITIVE SEAL BETWEEN MATING METAL PARTS, OFFERING A CLEAN, NON-OOZING APPLICATION. IT PERFORMS WELL AS A SOUND BARRIER AND VIBRATION DAMPENER.

PHYSICAL PROPERTIES:
ADHESION TO STEEL: 40 OZ / IN WIDTH
CHEMICAL RESISTANCE: GOOD
MOISTURE AND FUNGUS RESISTANCE: GOOD
THERMAL CONDUCTIVITY: .26 K-FACTOR AT 70? F ASTMC158
SERVICE TEMPERATURES: -015°F-160°F (-26°C- 71°C)
APPLICATION TEMPERATURES: 50°F - 160°F (- 26°C - 71°C)
DENSITY: 716
COMPRESSION DEFLECTION: 416 PER SQ. INCH
COMPRESSION SET: 14%

T-300 SINGLE FACED NEOPRENE FOAM TAPE

DESCRIPTION:
T-300 IS A PRESSURE SENSITIVE, ADHESIVE COATED POLYESTER FILM SUPPORTED, CLOSED CELL NEOPRENE BASED FOAM TAPE. THE HIGH PERFORMANCE ACRYLIC PRESSURE SENSITIVE ADHESIVE OFFERS APPLICATION TO MOST SURFACES, WHILE THE STRUCTURAL ADHESIVE LAMINATION OF STRETCH RESISTANT POLYESTER FILM TO NEOPRENE PROVIDES EXCELLENT PERFORMANCE WHEN EXPOSED TO ENVIRONMENTAL EXTREMES OF VIBRATION, TEMPERATURE AND HUMIDITY.

USES:
T-300 HAS SUCCESSFULLY BEEN USED AS A GASKET SEALER, SHOCK ABSORBER, INSULATOR AND IN WEATHER-STRIPPING APPLICATIONS.

PHYSICAL PROPERTIES:
ADHESION TO STEEL: 40 OZ / IN WIDTH
CHEMICAL RESISTANCE: GOOD
MOISTURE AND FUNGUS RESISTANCE: GOOD
WATER ABSORPTION (BY WEIGHT): 5%
SERVICE TEMPERATURES: -20°F - 200°F
APPLICATION TEMPERATURES: 50°F - 100°F

T-607 GLASS CLOTH TAPE

DESCRIPTION:
T-607S IS A GLASS CLOTH ELECTRICAL TAPE WITH A (STS) SILICONE THERMOSETTING ADHESIVE.
T-607R IS A GLASS CLOTH ELECTRICAL TAPE WITH A (RTS) RUBBER THERMOSETTING ADHESIVE.
T-607A IS A GLASS CLOTH ELECTRICAL TAPE WITH A (ATS) ACRYLIC THERMOSETTING ADHESIVE.

USES:
T-607 IS USED FOR COIL WRAP, CROSSOVER INSULATION, AND COIL BANDING.

FEATURES / BENEFITS:
THESE PRODUCTS HAVE COMBINED GLASS CLOTH WITH PRE- CURED ADHESIVES TO MAXIMIZE RESISTANCE TO FLAGGING AND VARNISH SOLVENTS. T-607S COMPLIES WITH FLAMMABILITY REQUIREMENTS (UL 510). BOTH THE T-607R AND THE T-607A COMPLY WITH FAR SPEC 25.853(A) AND FAR SPEC 25.855 (A-1).

PHYSICAL PROPERTIES:

	607R	607A	607S
INSULATION CLASS	130°C	155°C	180°C
TOTAL THICKNESS	7.0 MILS	7.0 MILS	7.0 MILS
BACKING THICKNESS	5.0 MILS	5.0 MILS	5.0 MILS
ADHESION TO STEEL	30 OZ / IN	30 OZ / IN	30 OZ / IN
ELONGATION	8%	8%	8%
BREAKING STRENGTH	170 LBS / IN	170 LBS / IN	170 LBS / IN
BREAKDOWN VOLTAGE	3000 VOLTS	1500 VOLTS	3000 VOLTS
COLOR	WHITE	WHITE	WHITE
ADHESIVE	RUBBER	ACRYLIC	SILICONE

T-609 UHMW TAPE

DESCRIPTION:
T-609 IS A SKIVED ULTRA HIGH MOLECULAR WEIGHT (UHMW) POLYETHYLENE FILM.
T-609 IS COATED WITH A PRESSURE SENSITIVE ELASTOMER ADHESIVE. AVAILABLE IN 5 MIL AND 10 MIL FILMS.

USES:
CAVITY LINER FOR BLISTER PACKAGING EQUIPMENT, COVERING FOR GUIDE RAILS AND CONVEYERS, LOW COST REPLACEMENT FOR TEFLON ? WHERE HIGH TEMPERATURE STABILITY IS NOT REQUIRED.

FEATURES / BENEFITS:
T-609 IS WEAR RESISTANT AND DURABLE. IT HAS A COEFFICIENT OF FRICTION AND GOOD ANTI-STICK QUALITIES. T-609 HAS A HIGH RESISTANCE TO CHEMICALS.

PHYSICAL PROPERTIES:

5 MIL:
TOTAL THICKNESS 9 MILS
BACKING THICKNESS 4 MILS
ADHESION TO STEEL 35 OZ / IN
TENSILE STRENGTH 35 LBS
OPERATING TEMPERATURE 225°F

10 MIL:
TOTAL THICKNESS 14 MILS
BACKING THICKNESS 4 MILS
ADHESION TO STEEL 35 OZ / IN
TENSILE STRENGTH 60 LBS
OPERATING TEMPERATURE 225°F

BACKING MATERIAL UHMW POLYETHYLENE RUBBER

T-610 SERIES OEM ELECTRICAL TAPES

DESCRIPTION

T-610C IS A CLEAR 1 MIL ABRASION RESISTANT POLYESTER FILM WITH A RUBBER ADHESIVE SYSTEM.
T-610Y IS A CLEAR 1 MIL ABRASION RESISTANT POLYESTER FILM WITH A RUBBER ADHESIVE SYSTEM.
T-6102C IS A CLEAR 1 MIL ABRASION RESISTANT POLYESTER FILM WITH AN ACRYLIC ADHESIVE SYSTEM.
T-6102Y IS A CLEAR 1 MIL ABRASION RESISTANT POLYESTER FILM WITH AN ACRYLIC ADHESIVE SYSTEM.
T-6105C IS A CLEAR 1 MIL ABRASION RESISTANT POLYESTER FILM WITH A RUBBER ADHESIVE SYSTEM.

USES:
T-610C AND T-610Y ARE IDEAL FOR COIL HOLDING, WRAPPING AND FINISHING. T-6102C AND T-6102Y ARE USED FOR HOLDING, INSULATING, WRAPPING, AND CAPACITOR TABBING. T-6105C IS HEAVY DUTY AND ABRASION RESISTANT MAKING IT AN EXCELLENT DIELECTRIC INSULATOR.

PHYSICAL PROPERTIES:

	610C	610Y	610-2C	610-2Y	6105C
BACKING THICKNESS	1.0 MIL	1.0 MIL	2.0 MIL	2.0 MIL	5.0 MIL
TOTAL THICKNESS	2.5 MIL	2.5 MIL	3.5 MIL	3.5 MIL	3.5 MIL
ADHESIVE	RUBBER	RUBBER	ACRYLIC	ACRYLIC	RUBBER
ADHESION TO STEEL	30-40 OZ/IN	45 OZ/IN	35 OZ/IN	35 OZ/IN	70 OZ/IN
TENSILE STRENGTH	23 LB/IN	25 LB/IN	50 LB/IN	50 LB/IN	100 LB/IN
DIELECTRIC STRENGTH	5000 VOLT	5000 VOLT	6500 VOLT	6500 VOLT	11000 VOLT
TEMPERATURE	130°C	130°C	130°C	130°C	130°C
ELONGATION	100%	80%	80%	80%	100%
UL APPROVED	YES	YES	YES	YES	NO

T-611 (HD) TEFLON* PFTE TAPE

DESCRIPTION:
T-611 (HD) IS A PRESSURE SENSITIVE TAPE USING TENSILIZED PFTE FILM WITH HIGH TEMPERATURE SILICONE ADHESIVE. THE TENSILIZED FILM PROVIDES HIGHER TENSILE STRENGTH, LOWER ELONGATION, AND HIGHER DIELECTRIC STRENGTH THAN REGULAR SKIVED FILM. THESE TAPES CONFORM TO MIL-I-23594C TYPE 1.

USES:
T-611 (HD) TAPE IS USED PRIMARILY IN ELECTRICAL APPLICATIONS SUCH AS COIL WRAPS AND SEPARATORS, TRANSFORMER AND HARNESS WRAPPING AND SLOT LINERS WHERE GOOD INSULATION AND HEAT RESISTANCE ARE NEEDED. THEY ARE ALSO USED IN MECHANICAL APPLICATIONS REQUIRING HIGH TEMPERATURE RESISTANCE AND NON-STICK SURFACES SUCH AS ROLL PROTECTION IN FLAT DIE EXTRUSION.

PHYSICAL PROPERTIES:

	T-611-2	T-611-3	T-611-5	T-611-10
FILM THICKNESS	002	.003	.005	.010
ADHESIVE THICKNESS	0015	.015	.015	.015
ADHESION	25 OZ/IN	30 OZ/IN	30 OZ/IN	30 OZ/IN
ELONGATION	100%	125%	125%	125%
DIELECTRIC STRENGTH	9000 VOLT	13000 VOLT	14000 VOLT	17000 VOLT
INSULATION RESISTANCE	2X10	2X10	2X10	2X10
OPERATING TEMPERATURES	500°F	500°F	500°F	500°F

*TEFLON IS A REGISTERED TRADEMARK OF DUPONT CORPORATION.

T-612 TEFLON PFTE GLASS CLOTH TAPE

DESCRIPTION:
T-612 IS A PFTE IMPREGNATED GLASS FABRIC WITH HIGH TEMPERATURE SILICONE ADHESIVE. THE PTFE PROVIDES A SMOOTH ANTI-STICK SURFACE, WHILE THE GLASS FABRIC PROVIDES STRENGTH AND DIMENSIONAL STABILITY.

USES:
T-612 APPLICATIONS INCLUDE: CONVEYOR BELT CONVERTING, HIGH TEMPERATURE MASKING, CHUTE / SLIDE COVERING FOR FOODS, CHEMICALS, PHARMACEUTICALS. DIE CUTTING OF GASKETS OR SEALS AND COVERING FOR HEAT SEALING AND PRINTING EQUIPMENT.

PHYSICAL PROPERTIES:
THICKNESS: 0.010''
ADHESIVE THICKNESS: 0.002''
ADHESION: 0.002 oz/ in
BREAKING STRENGTH: 225 LBS. / IN
MAX. OPERATING TEMP.: 500°F

T-690 DOUBLE COATED POLYETHYLENE FOAM TAPE

DESCRIPTION:
T-690 CLOSED CELL DOUBLE COATED P.E. FOAM TAPE WITH HIGH PERFORMANCE, SOLVENT RUBBER ADHESIVE SYSTEM. THIS PRODUCT HAS EXCELLENT HEAT, U.V. AND PLASTICIZER RESISTANCE.

USES:
T-690 IS TYPICALLY USED FOR MOUNTING AND JOINING ITEMS TO VARIOUS SURFACES.

FEATURES:
HIGH STRENGTH: HIGH TACK ADHESIVE FOR MAXIMUM LONG TERM HOLDING POWER, INDOORS OR OUT.

AVAILABILITY:
1/16'' 1/32'', OR 1/8'' THICKNESS, BLACK OR WHITE. 4 MIL. 70# SEMI-BLEACHED KRAFT LINER FOR EASY APPLICATION AND REMOVAL.

PHYSICAL PROPERTIES:
THICKNESS CARRIER ADHESIVE: 1/32'' FOAM (6LBS DENSITY) .023''-. 043'', 1/16' FOAM (4 LBS DENSITY) .054'' - .074''
LINER: .0040'' - .0046''
TENSILE LBS INCH WIDTH: 1/32'' - 5#-6# (PATC # 31) 1/16 '' - 9#- 10#
ADHESION: 100OZ / IN WIDTH (AVG.) (PSTC #31)
SHEAR: 24HRS. (AVG.) (PSTC# 7)
ELONGATION: 300.0% MIN. (PSTC #31)
LINER WEIGHT: 70 LBS. (24X36/500)
SUGGESTED APPLICATION TEMPERATURE: - 40°F + 160°F
SHELF LIFE: 2 YRS.

T-690A DOUBLE COATED POLYETHYLENE FOAM TAPE

DESCRIPTION:
T-690A IS A CLOSED CELL DOUBLE COATED P.E. FOAM TAPE WITH HIGH PERFORMANCE, SOLVENT ACRYLIC ADHESIVE SYSTEM. THIS PRODUCT HAS EXCELLENT HEAT, UV AND PLASTISIZER RESISTANCE.

USES:
TYPICALLY USED FOR MOUNTING OR JOINING ITEMS TO VARIOUS SURFACES.

FEATURES / BENEFITS:
HIGH STRENGTH. HIGH TACK ADHESIVE FOR MAXIMUM LONG TERM HOLDING POWER. INDOORS OR OUT.

AVAILABILITY:
1/16", OR 1/8" THICKNESS, WHITE OR BLACK. 4 MIL, 70# SEMI-BLEACHED KRAFT LINER FOR EASY APPLICATION AND REMOVAL.

PHYSICAL PROPERTIES:
THICKNESS CARRIER AND ADHESIVE:
1/32 " FOAM (6 LBS DENSITY) .023" - .043"
1/16" FOAM (4 LBS DENSITY) .054" - .074"
LINER: .0040" - .0046
TENSILE STRENGTH: 1/32" - 5 -6 LBS./ IN, 1/16" - 9 -10 LBS/ IN
ADHESION: 100 OZ / IN WIDTH
ELONGATION: 300 %
SUGGESTED APPLICATION TEMPERATURE: -40°F TO 160°F

T-800 ALUMINUM FOIL TAPE

T-800 IS A GENERAL PURPOSE ALUMINUM FOIL TAPE WITH ACRYLIC ADHESIVE.

PRINCIPAL USES;
T-800 ALUMINUM FOIL TAPE IS USED ON INSULATION BOARDS AND BATTS TO MAINTAIN THE INTEGRITY OF THE VAPOR BARRIER. DUE TO THE CONFORMITY OF DEAD SOFT FOIL, T-800 CAN BE USED ON IRREGULAR AND CURVED SURFACES.

FEATURES / BENEFITS:
T-800 FEATURES AN AGGRESSIVE ACRYLIC ADHESIVE SYSTEM WHICH IS ALL TEMPERATURE RATED TO PROVIDE SERVICE TEMPERATURES OF 0°F (-18°C) TO 150°F (66°C) AND APPLICATION TEMPERATURES OF 10°F (- 12°C) TO 120°F (49°C)

PHYSICAL PROPERTIES:
SUBSTRATE: DEAD SOFT ALUMINUM FOIL TEST METHOD
ADHESIVE: ACRYLIC
TAPE THICKNESS WITHOUT LINER SUBSTRATE: 1.5 MIL PSTC - 33 ASTM D3652
ADHESIVE: 1.25 MIL
COLOR: SILVER METALLIC
FLAME SPREAD: 5 UL 723 ASTM E-84
SMOKE GENERATED: 0 UL 723 ASTM E 84
PERMEANCE: 0.0 PERMS ASTM E 96
STORAGE TEMPERATURE: TAPE SHOULD BE STORED IN A COOL DRY AREA AT TEMPERATURES OF 60°F TO 80°F.

CAUTION: ALL PHYSICAL PROPERTIES LISTED ABOVE HAVE BEEN OBTAINED FROM RANDOM LABORATORY TESTING AND SHOULD NOT BE USED FOR THE PURPOSE OF WRITING SPECIFICATIONS. THE PRODUCT SHOULD BE TESTED TO DETERMINE THE SUITABILITY FOR ITS INTENDED USE.

T-800C ALUMINUM FOIL TAPE W / CONDUCTIVE ADHESIVE

DESCRIPTION:
T-800C IS A 2.0 MIL ALUMINUM FOIL TAPE WITH CONDUCTIVE ACRYLIC ADHESIVE.

USES:
T-800C IS SPECIFICALLY DESIGNED FOR EMI / RFI SHIELDING AND CABLE WRAP APPLICATIONS.

FEATURES / BENEFITS:
T-800C IS MANUFACTURE OF 2.0 MIL DEAD - SOFT ALUMINUM (1145-0) TO PROVIDE EXCELLENT CONFORMITY ON IRREGULAR AND CURVED SURFACES. THE ACRYLIC ADHESIVE IS UNIFORMLY DISPERSED WITH CONDUCTIVE SPHERES TO PROVIDE THE HIGHEST EMI /RFI SHIELDING EFFECTIVENESS AVAILABLE IN A CONDUCTIVE ALUMINUM FOIL TAPE. T-800C MEETS THE FLAME SPREAD REQUIREMENT OF UL 510. THE ELECTRICAL RESISTANCE MEETS THE MIL -STD-202C.

PHYSICAL PROPERTIES:
SUBSTRATE: DEAD SOFT ALUMINUM
ADHESIVE: CONDUCTIVE ACRYLIC
COLOR: SILVER METALLIC
THICKNESS: 4.0 MILS
ADHESION TO STEEL: 36 OZ/IN
TENSILE STRENGTH: 16 LB/IN
ELONGATION: 5%
ELECTRICAL RESISTANCE: .009 OHM /IN 2
FLAMMABILITY: FILE 130121

T-801 5 MIL LEAD FOIL INTERLINED

DESCRIPTION:
T-801 IS A 5 MIL LEAD FOIL TAPE WITH 3 MIL LINER.

USES:
T-801 LEAD FOIL TAPE IS USED FOR DECORATIVE LEADED WINDOWS OR AS A VAPOR BARRIER. T-801 CAN ALSO BE USED FOR RADIATION / X-RAY SHIELDING AND AS A MASK FOR ELECTRO-PLATING.

FEATURES / BENEFITS:
T-801 IS COATED WITH AN AGGRESSIVE ACRYLIC ADHESIVE OFFERING GOOD SOLVENT RESISTANCE AND EXCELLENT AGING CHARACTERISTICS. T-801 IS VERY CONFORMABLE, OFFERING ONE OF THE MOST VERSATILE LEAD TAPES IN THE INDUSTRY.

PHYSICAL PROPERTIES:
SUBSTRATE: LEAD FOIL
ADHESIVE: ACRYLIC 1 MIL
FOIL THICKNESS: 5.0 MILS
LINER: 3.0 MIL
ADHESION TO STEEL: 45 OZ / IN
TENSILE STRENGTH: 20 LBS / IN
GOVERNMENT SPEC.: HH-T-29A AMENDMENT 2

T-803 COLORED VINYL TAPE

DESCRIPTION:
T-803 IS POLY VINYL CHLORIDE TAPE THAT IS THIN, STRONG AND VERY CONFORMABLE. T-803 COMES WITH A SPECIAL PROPRIETARY RUBBER BASED ADHESIVE SYSTEM.

USES:
T-803 CAN BE USED TO SEAL CONTAINERS, COLOR CODE A VARIETY OF ITEMS, MASKING CIRCUIT BOARDS, FLOOR MARKING, ABRASION PROTECTION AND DECORATIVE IDENTIFICATION
T-803 IS AVAILABLE IN 8 OSHA COLORS. T-803 HAS AN EXCELLENT RESISTANCE TO ACIDS, ALKALIS, BACTERIA CORROSION AND OILS. T-803 MAKES A NEAR PERFECT VAPOR BARRIER AND IS HIGHLY ABRASIVE AND RIP RESISTANT. T-803 IS ECONOMICAL, WEATHERS WELL, CAN BE WRITTEN ON AND IS EASILY REMOVED OR REPLACED.

PHYSICAL PROPERTIES:
TENSILE STRENGTH: 18 LBS/IN
ADHESION: 25 OZ/ IN
THICKNESS: 5 MILS
ELONGATION: 150%
TEMPERATURE RANGE: 40°F- 170°F
MOISTURE RESISTANCE: GOOD

T-805 KAPTON* FILM

DESCRIPTION:
T-805 KAPTON TAPE IS A TRANSPARENT, AMBER COLORED POLYMIDE FILM WITH A PRESSURE SENSITIVE SILICONE ADHESIVE SYSTEM. T-805 CONFORMS TO MIL. SPEC: MIL-P-46112, TYPE I.

USES:
T-805 IS USED FOR FLAME RESISTANT ELECTRICAL INSULATION, WIRE AND CABLE WRAP, WIRE BUNDLING TERMINATION, SPLICING OF HIGH TEMP. REFLECTIVE THERMAL INSULATING FILM. T-805 IS AN EXCELLENT SOLDER MASK FOR CIRCUIT BOARDS. RELEASE SURFACE FOR HEATED PLATENS IN HEAT SEALING / LAMINATION.

FEATURES / BENEFITS:
HEAT RESISTANT FILM: RESISTS HIGH HEAT OF MOLTEN SOLDER TEMPERATURES OF 100 F-500 F. SHORT EXPOSURE UP TO 700 F.
SPECIAL ADHESIVE: FUNCTIONS DURING HIGH TEMP SOLDERING AND LEAVES MINIMAL RESIDUE WHEN REMOVED AFTER MANUFACTURING PROCESS.
TRANSPARENT: PERMITS OBSERVATION OF THE CIRCUIT BOARD DURING PROCESS.

PHYSICAL PROPERTIES:
BACKING: POLYMIDE FILM
COLOR: AMBER, TRANSPARENT
ADHESIVE: SILICONE
TOTAL THICKNESS: 2.5 MIL
ADHESION TO STEEL: 25 OZ./IN
ELONGATION: 60% MIN.
TENSILE STRENGTH: 30 LBS./ IN
GOVT. SPECIFICATION: MIL-P-46112, TYPE I
DIELECTRIC STRENGTH: 7500 VOLTS
FLAMMABILITY RATING: COMPLIES W / UL-510 STANDARD
UL COMPONENT RECOG.: GUIDE DANZ2, FILE E20392

EQUIVALENT PRODUCTS; 3M #5413 PERMACELL #P-221

SHELF LIFE: 1 YEAR

*KAPTON IS A REGISTERED TRADEMARK OF DUPONT CORPORATION.

T-805A KAPTON TAPE

DESCRIPTION:
T-805A IS A 1 MIL POLIMIDE FILM TAPE WITH AN ACRYLIC BASED ADHESIVE SYSTEM.

USES:
T-805A IS HIGH TEMPERATURE TRANSFORMER INSULATOR WHERE SILICONE CANT BE USED.

PHYSICAL PROPERTIES:
INSULATION CLASS: 155°C
TOTAL THICKNESS: 2.5 MILS
BACKING THICKNESS: 1.0 MIL
ADHESION TO STEEL: 35 OZ/IN
ELONGATION: 35%
BREAKING STRENGTH: 30 LBS/IN
BREAKDOWN VOLTAGE: 7500 VOLTS

T-805 AS KAPTON TAPE

DESCRIPTION:
T-805AS IS A HIGH PERFORMANCE POLYMIDE FILM THAT PROVIDES THE ULTIMATE IN PRINTED CIRCUIT BOARD PROTECTION. IT IS DESIGNED WITH BOTH A CONDUCTIVE BACKING FILM AND ADHESIVE TO MINIMIZE "STATIC" EFFECTS DURING STRIPPING AND PEALING. THIN AND CONFORMABLE, WITH OUTSTANDING PUNCTURE, TEAR AND ABRASION RESISTANCE AT ELEVATED TEMPERATURES. GOLD FINGERS ARE SAFE FROM SOLDER DEFECTS AND COSTLY REWORKS ARE ELIMINATED. FEATURING A SPECIALLY FORMULATED SILICONE ADHESIVE THAT PROVIDES HIGH TEMPERATURE RESISTANCE AND LEAVES NO ADHESIVE RESIDUE UPON REMOVAL. OPTIMAL PRODUCT FOR GOLD FINGER PROTECTION DURING WAVE SOLDER.

FEATURES:
T-805AS HAS ANTI-STATIC BACKING AND A CONDUCTIVE ADHESIVE THAT IS THIN AND CONFORMABLE. T-805AS IS ALSO RESISTANT TO CORROSIVE CHEMICALS.

PHYSICAL PROPERTIES:
CARRIER: . 001" POLYMIDE-KAPTON
COLOR: AMBER
TOTAL THICKNESS: .0025"(2.5 MIL)
ADHESIVE THICKNESS: .0015"(1.5 MIL)
OPERATING TEMPERATURE RANGE: 100°F TO 500°F

ELECTRICAL PROPERTIES:
STATIC CHARGE @ 50% R.H. 70°F IN ESD CONTROLLED ENVIRONMENT
REMOVAL FROM ROLL < 50 VOLTS
REMOVAL FROM PCB < 50 VOLTS
DIELECTRIC STRENGTH 6800 VOLTS

T-805 3.5 MIL KAPTON FILM

DESCRIPTION:
T-805 3.5 MIL KAPTON TAPE IS ENGINEERED FOR HEAVY DUTY, HIGH TEMPERATURE APPLICATIONS WHERE ONE MIL POLYMIDE DOESN’T PROVIDE ADEQUATE STRENGTH OF PHYSICAL PROTECTION. INHERENTLY FLAME-RETARDANT.

USES:
T-805 3.5 MIL KAPTON IS USED FOR FLAME RESISTANT ELECTRICAL INSULATION, WIRE AND CABLE WRAP, WIRE BUNDLING TERMINATION, SPLICING OF HIGH TEMP. REFLECTIVE THERMAL INSULATING FILM. T-805 3.5 MIL.IS EXCELLENT SOLDER MASK FOR CIRCUIT BOARDS. RELEASE SURFACE FOR HEATED PLATENS IN HEAT SEALING / LAMINATION.

FEATURES / BENEFITS:
UNEXCELLED PHYSICAL AND ELECTRICAL PROPERTIES ARE RETAINED AT HIGHER TEMPERATURES THAN ANY OTHER FLEXIBLE INSULATION.
THE AGGRESSIVE SILICONE ADHESIVE IS SOLVENT RESISTANT, AND COMPLIMENTS THE POLYMIDE BACKING TO PRODUCE A TAPE WITH EXCEPTIONAL HIGH TEMP. PROPERTIES.
TOUGH BACKING PROVIDES THE ULTIMATE IN TENSILE, TEAR, PUNCTURE AND ABRASION RESISTANCE WHEN USED WITH MEDIUM AND HEAVY GAUGE MAGNET WIRE.
VERY HIGH DIELECTRIC STRENGTH FOR CRITICAL INSULATING REQUIREMENTS.

PHYSICAL PROPERTIES:
BACKING: 2 MIL POLYMIDE FILM
COLOR: AMBER, TRANSPARENT
ADHESIVE: 1.5 MILS. SILICONE, CURED
TOTAL THICKNESS: 3.5 MIL.
ADHESION TO STEEL: 25 OZ./IN
ELONGATION: 65% MIN.
TENSILE STRENGTH: 60 LBS./ IN
GOVT. SPECIFICATION: MIL-P-46112, TYPE I
DIELECTRIC STRENGTH: 11,500 VOLTS
FLAMMABILITY RATING: COMPLIES W / UL-510 STANDARD
UL COMPONENT RECOG.: GUIDE DANZ2, FILE E20392

EQUIVALENT PRODUCTS: PERMACELL #P-222

SHELF LIFE: 1 YEAR

T-806 POLYIMIDE FILM TAPE

DESCRIPTION:
T-806 IS A TRANSPARENT AMBER COLORED POLYIMIDE FILM TAPE WITH A PRESSURE SENSITIVE SILICONE ADHESIVE SYSTEM.

USES:
T-806 IS USED FOR FLAME RESISTANT ELECTRICAL INSULATION, WIRE AND CABLE WRAP, WIRE BUNDLING TERMINATION, SPLICING OF HIGH TEMPERATURE REFLECTIVE THERMAL INSULATING FILM. T-806 IS AN EXCELLENT SOLDER MASK FOR CIRCUIT BOARDS. RELEASE SURFACE FOR HEATED PLATENS IN HEAT SEALING / LAMINATION.

FEATURES / BENEFITS:
HEAT RESISTANT FILM: RESISTS HIGH HEAT OF MOLTEN SOLDER TEMPERATURES OF 100°F TO 500°F SHORT EXPOSURE UP TO 600°F.
SPECIAL ADHESIVE: FUNCTIONS DURING HIGH-TEMP SOLDERING AND LEAVES MINIMAL RESIDUE WHEN REMOVED AFTER MANUFACTURING PROCESS.
TRANSPARENT: PERMITS OBSERVATION OF CIRCUIT BOARD DURING PROCESS.

PHYSICAL PROPERTIES:
BACKING: POLYIMIDE
COLOR: AMBER, TRANSPARENT
ADHESIVE: SILICONE
TOTAL THICKNESS: 2.2 MILS
ADHESION TO STEEL: 20 OZ /IN
ELONGATION: 60% MIN.
TENSILE STRENGTH: 23 LBS / IN

T-807 CIRCUIT BOARD TAPE

DESCRIPTION:
T-807 IS A TRANSPARENT BLUE POLYESTER FILM WITH PRESSURE SENSITIVE SILICONE ADHESIVE.

USES:
T-807 IS AM CIRCUIT BOARD MASK WITH A SUPERIOR "STOP OFF LINE", PROTECTING THE CIRCUITRY FROM SPLASHES AND FUMES OF CHEMICALS USED IN TIN / LEAD STRIPPING AND GOLD TAB PLATING. T-807 IS DESIGNED TO PERFORM IN ALL PHASES OF THE MASKING OPERATIONS DURING PRINTED CIRCUIT BOARD PRODUCTION.

FEATURES / BENEFITS:
SPECIAL ADHESIVES, RESISTS FUMES AND CHEMICALS AND LEAVES MINIMAL RESIDUE. CONTROLLED UNWIND, PERMITS EASY, MANUAL OR MACHINE APPLICATION. TRANSPARENT FILM ALLOWS VISIBILITY OF CIRCUITRY AFTER MASKING. THE TOUGH FILM WILL NOT BREAK OR SPLIT DURING APPLICATION OR REMOVAL.

PHYSICAL PROPERTIES:
BACKING: POLYESTER
COLOR: BLUE, TRANSPARENT
TOTAL THICKNESS: 3 MIL
ELONGATION: 100%
ADHESIVE: SILICONE
ADHESION TO STEEL: 20 OZ/IN
TENSILE STRENGTH: 23 LBS/ IN

T-811 OUTDOOR MASKING TAPE

DESCRIPTION:
T-811 IS A NEW, BLUE CREPE, OUTDOOR MASKING TAPE.

USES:
T-811 CAN BE USED WHENEVER TAPE WILL BE LEFT ON A SURFACE FOR AN EXTENDED PERIOD IF TIME. IT CAN BE USED ON DELICATE SURFACES WHERE IT IS CRITICAL NOT TO HAVE ADHESIVE RESIDUE LEFT WHEN THE TAPE IS REMOVED. T-811 IS IDEAL ON SURFACES THAT ARE EXPOSED TO SUNLIGHT. IT CAN BE USED WHENEVER A FINE PAINT LINE OR SUPERIOR COLOR SEPARATION IS NEEDED.

FEATURES / BENEFITS:
T-811 WILL NOT LEAVE ADHESIVE RESIDUE. IT RESISTS EXPOSURE TO SUNLIGHT AND OTHER SOURCES OF ULTRA-VIOLET RADIATION. T-811 CAN BE LEFT ON SURFACES FOR UP TO 14 DAYS AND WILL REMOVE EASILY.
T-811 USES AN ENVIRONMENTALLY FRIENDLY ADHESIVE THAT DOES USE HARMFUL HYDROCARBON SOLVENTS. EASY UNWIND AND HIGHLY CONFORMABLE.

PHYSICAL PROPERTIES:
BACKING: MATERIAL BLUE CREPE PAPER
ADHESION TO STEEL: 20 OZ / IN
QUICK STICK: 10 OZ / IN
ELONGATION: 6%
TENSILE STRENGTH: 25 LBS / IN
GAUGE: 5.5 MILS

EQUIVALENT: 3M #2090 LONG MASK BLUE

T-905 LOW DENSITY POLYETHYLENE FILM

DESCRIPTION:
T-905 IS A 5 MIL POLYETHYLENE FILM TAPE. AVAILABLE IN RED, WHITE, BLACK, DARK BLUE, LIGHT BLUE, GREEN, ORANGE, YELLOW, BROWN, AND CLEAR. (PURPLE ON SPECIAL ORDER).

USES:
T-905 PROVIDES THE ADDED DIMENSION OF COLOR TO APPLICATIONS REQUIRING DECORATIVE COVERING AND TRIM, AS WELL AS DURABILITY AND WEATHER ABILITY. THIS PRODUCT IS LOW IN HALOGENS AND LEACHABLE CHLORIDES.

FEATURES / BENEFITS:
GOOD CHEMICAL RESISTANCE, EXCELLENT MOISTURE BARRIER PROPERTIES, EXCELLENT CONFORMABILITY, WIDE TEMPERATURE RANGE PERFORMANCE, UV RESISTANCE, PERMANENT BOND AND LONG AGING CHARACTERISTICS OF AN ACRYLIC ADHESIVE.

PHYSICAL PROPERTIES:
SUBSTRATE: LOW DENSITY POLYETHYLENE FILM
ADHESIVE: ACRYLIC
TOTAL THICKNESS: 5 MIL
TENSILE STRENGTH: 10 LBS/IN
ELONGATION: 650%
ADHESION TO STEEL: 40 OZ/IN
OPERATING TEMPERATURE: -40°F-200°F
APPLICATION TEMPERATURE: 20°F-120°F

T-910 HOOK AND LOOP VELCRO

DESCRIPTION:
T-910 IS WOVEN NYLON HOOK AND LOOP CONSISTING OF TWO MATING TAPES. THE HOOK TAPE HAS ROWS OF MINUTE, FLEXIBLE HOOK. THE LOOP TAPE IS COMPRISED OF HUNDREDS OF SMALL DISORIENTED SOFT LOOPS. WHEN THE TWO TAPES ARE PRESSED TOGETHER, THE HOOKS ENGAGE THE LOOPS FORMING A HIGHLY SECURE CLOSURE, WHICH IS COMPLETELY JAM PROOF AND ADJUSTABLE. TO OPEN, THE CLOSURE IS SIMPLY PULLED APART.

USES:
T-910 CAN BE ATTACHED TO MOST FLAT SURFACES. THE SURFACES MUST BE CLEAN, DRY AND FREE OF OIL. REMOVE THE PROTECTIVE LINER AND PRESS THE FASTENER FIRMLY IN PLACE. A RUBBER ROLLER WORKS WELL AND ASSURES GOOD UNIFORM CONTACT BETWEEN THE ADHESIVE AND SUBSTRATE. ADHESION WILL INCREASE OVER A PERIOD OF SEVERAL HOURS. SURFACES TO BE BONDED SHOULD BE ABOVE 65? F. IDEAL FOR USES IN ELECTRONICS. MEDICAL, AUTOMATION, UTILITIES, SPORTING GOODS AND BOATING.
COLORS: WHITE, BLACK, RED, NAVY, BEIGE, GREEN, BROWN ETC.

WIDTHS AVAILABLE: 5/8", 3/8", 1", 1 1/2", 2", 4"

ADHESIVES: RUBBER AND ACRYLIC ADHESIVES ARE AVAILABLE

CYCLE LIFE: AFTER 25,000 CYCLES, T-910 HOOK AND LOOP CLOSURE HAS A SHEAR STRENGTH OF 10 PSI. HOWEVER EXPERIENCE SHOWS AFTER 50,000 CYCLES THE CLOSURE RETAINS 8 PSI. THE ABOVE DATA IS THE RESULT OF TESTS PERFORMED UNDER CONTROLLED LABORATORY CONDITIONS OF -70°F TO 200°F.

DIE CUT P/S HOOK AND LOOP DOTS: 1/2 ", 5/8", 3/4", 7/8", 1 3/8", 1 7/8"

OTHER PRODUCTS: HI TEMP TO 800°F, FLAME-RETARDANT, CONDUCTIVE RFI SHIELDING, SOLVENT AND HEAT ACTIVATED PRODUCTS.

T-915C COPPER FOIL CONDUCTIVE TAPE

DESCRIPTION:
T-915C IS A COPPER FOIL MANUFACTURED WITH AN ACRYLIC SOLVENT RESISTANT / CONDUCTIVE ADHESIVE.

USES:
T-915C IS USED TO MEET A VARIETY OF EMI /RFI SHIELDING APPLICATIONS IN THE ELECTRONICS INDUSTRY. T-915C IS ALSO AN ADD ON FOR PLATING BARS AND GOLD FINGERS IN THE CIRCUIT BOARD INDUSTRY. IT COMES WITH A LINER FOR EASY DIE CUTTING.

PHYSICAL PROPERTIES:
BACKING MATERIAL: 1 OZ COPPER FOIL
ADHESIVE: CONDUCTIVE ACRYLIC
TOTAL THICKNESS: 3.5 MILS
ADHESION TO STEEL: 45 OZ / IN WIDTH
TENSILE STRENGTH: 35 LBS/ IN
COLOR: COPPER
ELECTRICAL RESISTANCE: 0.005 OHMS / IN SQ.
FREQUENCY (MHz): 90-90 DB, 100-80 DB, 600-78 DB, 1000-78 DB
OPERATING TEMPERATURES 155°C

T-920 PROTECTIVE FILM

DESCRIPTION:
T-920 IS A HIGH PERFORMANCE FILM COATED WITH A SPECIALLY FORMULATED WATER BASED PRESSURE SENSITIVE ACRYLIC ADHESIVE.

USES:
T-920 IS USED AS A MASK ON THE INSIDE (TOP) OR FLAT SIDE (BOTTOM) OF SILK SCREEN ASSEMBLIES TO PREVENT SOLVENT BASED INK BLEED. WHEN T-920 IS USED TOP AND BOTTOM, IT INCREASES SOLVENT RESISTANCE. IT CAN ALSO BE USED TO BLOCK OUT A PORTION OF SCREEN WHEN PRINTING.

FEATURES / BENEFITS:
REDUCES CLEAN UP TIME. TRANSLUCENT FOR EASY PLACEMENT. LEAVES NO RESIDUE. REMOVES IN ONE PIECE. WITHSTANDS THE STRESS OF RETENSIONING AND IS ABRASION RESISTANT.

PHYSICAL PROPERTIES:
TOTAL THICKNESS: 3 MILS
COLOR: CLEAR
TENSILE STRENGTH: 17 LBS / IN
ELONGATION: 300 %
ADHESION TO STEEL: 4-6 OZ
ROLL LENGTH: 200 YARDS

T-970 POWDER COATING

DESCRIPTION:
T-970 HIGH TEMPERATURE SPLICING AND MASKING TAPE. POLYESTER FILM, TRANSPARENT, BLUE, PRESSURE SENSITIVE SILICONE ADHESIVE SYSTEM.

USES:
DESIGNED TO PERFORM IN ALL PHASES OF SPLICING SILICONE RELEASE COATED PAPERS, TEXTILES AND FILMS. EXCELLENT FOR MASKING IN POWDER AND WET COATING OPERATIONS.

FEATURES / BENEFITS:
SPECIAL ADHESIVES: RESISTS FUMES AND CHEMICALS. LEAVES MINIMAL RESIDUE UPON REMOVAL.
CONTROLLED UNWIND: PERMITS EASY MANUAL OR MACHINE APPLICATION. LEAVES MINIMAL RESIDUE WHEN REMOVED AFTER MANUFACTURING PROCESS. REDUCES CLEAN UP TIME AND MINIMIZES REJECTS.
TOUGH FILM: WILL NOT BREAK OR TEAR DURING APPLICATION OR REMOVAL.

PHYSICAL PROPERTIES:
BACKING: POLYESTER 2.0 MILS
TOTAL THICKNESS: 3.5 MILS
COLOR: BLUE TRANSPARENT (CALL FOR OTHER COLOR AVAILABILITY)
ELONGATION: 130% MINIMUM
ADHESIVE: SILICONE SYSTEM / .0015 MILS
ADHESION TO STEEL: 35 OZ. / INCH WIDTH
TENSILE: 30 LBS / INCH WIDTH

T-980 HOT AIR LEVELING TAPE

DESCRIPTION:
T-980 IS A HIGH PERFORMANCE P.C. BOARD TAPE, PROVIDING CLEAN REMOVAL ON HIGH TEMPERATURE MASKING APPLICATIONS. T-980 IS MADE OF FLAT PAPER REINFORCED WITH POLYESTER FILM AND THEN COATED WITH AN AGGRESSIVE SILICONE ADHESIVE TO WITH STAND THE RIGORS OF HOT AIR LEVELING. T-980 FEATURES EXCELLENT CHEMICAL AND HOT SOLDER RESISTANCE, WITH GOOD CONFORMABILITY TO INSURE SECURE BONDING.

APPLICATIONS:
T-980 IS SPECIFICALLY DESIGNED TO FULLY PROTECT GOLD OR RHODIUM PLATED P.C. BOARD FINGER CONTACTS, THROUGH THE FLUX AND HIGH HEAT OF MOLTEN SOLDER DURING SOLDER COATING AND HOT AIR LEVELING.

SHELF LIFE: 6 MONTHS AFTER DATE OF PURCHASE, WHEN STORED IN THE ORIGINAL CARTON AT 73°F AND 65% HUMIDITY.

T-997 ESD GRID TAPE

DESCRIPTION: T-997 IS A CONDUCTIVE GRID ADHESIVE TAPE THAT IS PERMANENTLY STATIC FREE.

USES: T-997 IS TYPICALLY USED FOR MARKING GRIDS.

FEATURES / BENEFITS:
T-997 HAS EXCELLENT SHIELDING PROPERTIES PROVIDING RELIABLE PROTECTION AGAINST ESD DAMAGE TO SENSITIVE DEVICES. T-997 HAS NO CARBON FALL-OUT, WHICH MAKES IT IDEAL FOR CLEAN ROOM APPLICATIONS. T-997 MEETS WITH MIL-STD-81705B DECAY TEST.

PHYSICAL PROPERTIES:
TEST METHOD:
TENSILE STRENGTH - LONGITUDINAL 160 LBS N / MM SQ. ASTM D 882
TENSILE STRENGTH - TRANSVERSE 270 LBS N / MM SQ. ASTM D 882
ELONGATION - LONGITUDINAL 160% ASTM D 882
ELONGATION - TRANSVERSE 50 % ASTM D 882
BASE FILM THICKNESS: 30 MICRON
PEELING FORCE: 12 N
STATIC DECAY TIME: 0.5 SEC. FTMS 101B@15% RH, 73°F METHOD 4046

X-65 ESD HIGH TEMPERATURE MASKING

DESCRIPTION:
X-65 IS A HIGH PERFORMANCE TAPE WITH A SPECIALLY TREATED PAPER BASE, A HEAT AND CHEMICAL RESISTANT COATING AND A SPECIALLY FORMULATED ADHESIVE.

USES:
X-65 IS AN EXCELLENT NON STATIC MASKING TAPE. IT FULLY PROTECTS GOLD PLATED PRINTED CIRCUIT BOARD FINGER TABS ANDS ASSEMBLY HOLES THOUGH THE PRE CLEAN, FLUX, PRE-HEAT AND SOLDER TEMPERATURES ASSOCIATED WITH WAVE SOLDERING AND HOT AIR LEVELING. X-65 CAN BE APPLIED COLD OR WITH SLIGHT HEAT SUCH AS A HEATED TAPE SQUASHER.

FEATURES:
• X-65 HAS A SPECIAL CHEMICAL RESISTANT COATING AND WILL PERFORM AT TEMPERATURES OP TO 500 DEG F.
• X-65 FUNCTIONS DURING HIGH TEMP APPLICATIONS DUE TO A SPECIALLY FORMULATED ADHESIVE.

REMOVES CLEANLY WITH NO RESIDUE

PHYSICAL PROPERTIES:
BACKING: 4.0 MIL / HIGH TEMPERATURE FLAT BACK PAPER
ADHESIVE: SILICONE / ORGANIC
COLOR: WHITE
TOTAL THICKNESS: 6 MILS
TENSILE STRENGTH: 26 LBS. / IN WIDTH
ELONGATION: 3%
ADHESION TO STEEL: 40 OZ / IN WIDTH
TEMPERATURE: UP TO 550°F.

BD-1

DESCRIPTION:
BD-1 IS ENGINEERED TO HANDLE A VARIETY OF AXIAL LEAD ELECTRONIC COMPONENT REEL PACKAGING AND SEQUENCING APPLICATIONS. RECOMMENDED FOR USE WHERE REEL PACKAGING IS A SEPARATE OPERATION AND IS NOT PART OF A CONTINUOUS COMPONENT PRODUCTION AND TAPING PROCESS…AND / OR WHEN TENSILE AND TEAR STRENGTH REQUIREMENTS ARE REDUCED BY THE USE OF EQUIPMENT THAT MINIMIZES TAPE RUNNING TENSION AND START UP LOADS. AN EXCELLENT CHOICE FOR "QUICK TURNAROUND" SEQUENCING OPERATIONS.

FEATURES / BENEFITS:
LOW ELONGATION MAKES FOR DEPENDABLE MAINTENANCE OF COMPONENT SPACING DURING ASSEMBLY…YET IS SUFFICIENT TO ASSURE CONTOURED LAY-DOWN OF TAPE AROUND COMPONENT LEADS.
HIGH STRENGTH ADHESIVE PROVIDES GOOD MASS TO MASS BOND, ASSURING TAPED COMPONENTS ARE SECURELY HELD IN THEIR REQUIRED POSITIONS.
CONTROLLED LOW, UNIFORM ROLL AND SPOOL UNWIND MINIMIZES TAPE BREAKAGE, PERMITTING TROUBLE FREE PRODUCTION.
AVAILABLE IN THREE COLORS - WHITE, BLUE AND RED- TO PROVIDE FOR POLARITY AND OTHER DESIGNATIONS.

TECHNICAL DATA:
BACKING MATERIAL: FLAT KRAFT PAPER
ADHESIVE: SYNTHETIC RUBBER / RESIN
COLORS: WHITE, BLUE AND RED
TOTAL TAPE THICKNESS: 6.0 MILS/0.152 MM
ADHESION TO STEEL: 60 OZ. PER IN./ 670 GM PER CM
TENSILE STRENGTH: 25 LBS PER IN./ 4.5 KG PER CM
ELONGATION: 3%
EIA STANDARD: RS-296-D

LONG LENGTH SPOOLS MINIMIZE PRODUCTION DOWNTIME BY SUBSTANTIALLY REDUCING THE NUMBER OF ROLL CHANGES REQUIRED. HIGH ADHESIVE MASS ANCHORAGE , RIGIDLY SECURES AXIAL LEAD COMPONENTS.

Please call or e-mail for a prompt, competitive quote.

Please Click Below For:

E-MAIL: info@tapes2.com

Tapes II International

Tape and Fabrication Company

2909 West Pendleton Avenue, Santa Ana, CA 92704

714-641-8858 FAX 714-979-6217